TOOLS & CHEMICALS FRAME & SUSPENSION TOOLS 01 HELMETS & AUDIO 6082 PROFESSIONAL BIKE ALIGNMENT 02 SEAT TOOL WITH LASER 03 EXHAUST 04 ELECTRIC & LIGHT 05 ENGINE ELECTRICS INTAKE 06 ENGINE 07 PRIMARY & CLUTCH 08 TRANSMISSION 09 GASKET & SEALS 10 FINAL DRIVE 11 WHEELS & TIRES 12 BRAKE A professional tool for workshop use, allowing you to check wheel alignment within minutes. First you check if the final drive is in line with the included Chain Alignment Tool, than attach the CNC machined aluminum gauges to the front and rear wheel and switch on the laser and you can see at a glance if the wheels are in line or not. The two gauges with integrated class‑2 lasers guarantee a measuring tolerance of less than 0.5mm/ meter. No more hassling around with ropes or bars of steel, the Bike Alignment Tool (B.A.T.) gives secure information. Perfect for Custom Bike Builders, crash damage controls, and a real help in solving road‑holding problems. Professionals know that professional tools require professional care, so the B.A.T. comes complete with a high impact plastic case to store it properly. 13 HANDLEBAR, HAND CONTROLS & 14 MIRRORS CONTROL CABLES & HYDRAULIC LINES 1 1 5 6 FOOT CONTROLS Complete kit contains: • Laser Chain Alignment Tool with two 1.5 Volt LR44 batteries • One pair front wheel gauges with clamps • One pair rear wheel gauges with clamps • High Impact plastic case • Two laser equipped gauges 701226 Professional Bike Alignment Tool 17 FRONT FORKS 18 FRAME & REAR SUSPENSION 19 FENDER & STRUTS 6081 JIMS FLH/FLT POWER TRAIN ALIGNMENT TOOL 20 GAS- & OIL TANK 21 GAUGES & DASHES 22 OIL, OIL FILTERS & OIL COOLERS 23 HARDWARE This tool easily and safely aligns the Power Train to the correct position on most 1993 WINDSHIELD to present (rubber engine, transmission 24 and swingarm mounted) Touring models. Alignment service must be performed LUGGAGE when the engine, transmission, or 25 swingarm have either been removed or repaired. Without accurate alignment the TOOLS&CHEMICALS safety in handling and performance will be effected. 26 751073 Power train alignment tool TECH TIPS & CROSS 27 REF OEM>ZPN 28 ALPHABETICAL INDEX 26-052 6083 JIMS VACUUM FED FORK FILLING TOOL This easy to use tool will eliminate the need on Touring models to remove the fairing in order to change the fork oil. To drain the fluid, simply insert the tapered fitting into the drain hole and create a vacuum using the separately available Sonic over & under pressure kit. Once you reach approximately 23lbs. of vacuum pressure, rotate the valve and instantly the vacuum will draw the pre‑measured amount of fork fluid into the fork tube. Note: Not for use with cartridge type forks, Upside Down and other inverted fork assemblies 745671 Sonic over & under pressure kit 751135 Jims Vacuum fork filling tool 6084 FORK TUBE SPRING RETAINER REMOVER/INSTALLER TOOL This tool has two pins to match the front fork spring retainer screw on early drum brake Sportsters and Superglides. Locate this tool with the pins facing down on top of the spring retainers inside the fork tube. You will then be able to remove or install this retainer to service the fork assembly. 751065 Fits Sportsters 1952 thru 1972, and Superglide FX models 1970 thru 1972 6085 41MM FORK SEAL AND BUSHING INSTALLATION TOOL Designed for easy installation of the fork slider bushing and oil seals on 1984 thru 2017 41mm forks. With the fork tube installed in the lower fork as a guide for the 2 kilos weighing tool you can use one side of the tool to install the fork slider bushing exactly on depth, the other side to install the fork seal. Use of the tool prevents for damage and guarantees a perfect square installation of both seals and bushings. 351144 41mm fork seal and bushing installation tool 6086 JIMS FORK TUBE PLUG SOCKET FOR 49MM FORKS 753696 Works on 2014 to present Touring and Trike 6091 JIMS FORK CAP INSTALLATION TOOL Use this tool with a pair of Quick Clamps to install fork tube caps without removing the fork legs from the motorcycle. 753692 Works on all 49mm forks 6087 JIMS FRONT FORK COMPRESSOR TOOLS 1984 to present fork springs in cartridge style 41mm fork assemblies require com‑ pression when servicing or re‑building. This compressor can be mounted in a vice for easy hands free servicing. Includes an adapter for FL forks to eliminate direct contact with spring coil. Also includes a special rod to pull the fork damper rod. Tool works with stock length forks. 751066 Tool for stock length forks 6089 JIMS 49MM FORK DUST AND FORK SEAL INSTALLER TOOL This two‑piece tool is designed to install the lower leg 49mm fork seal squarely into the bore without damaging the seal lip surface. Works on 2016 to present XL1200X Forty‑Eight, 2016 to present XL1200CX Roadster, 2006 thru 2017 Dyna, 2002 thru 2017 V‑Rod, 2016‑2017 FXSE Pro‑Street Breakout, all 2018 to present Softail and 2014 to present Touring. 751128 Jims 49mm fork dust seal and oil seal installer 6090 JIMS CASTLE NUT TOOL FOR HAR‑ LEY‑DAVIDSON INVERTED FORKS The right side fork leg on OEM Harley in‑ verted forks features a special castle nut to secure and compress the fork spring. This solid steel socket helps to remove and install this special nut. Works on 2018 to present FLSB Sport Glide, 2019 to present FXDR, 2018 to present FXFB & FXFBS Fat Bob, 2016‑2017 FXSE Pro Street Breakout, 2012‑2017 VRSCDX Night Rod Special, 2009‑2017 VRSCF V‑Rod Muscle, 2016 to present XL1200CX Roadster and 2008‑2010 XR1200. 756311 Castle nut tool for Upside Down Harley forks
Download PDF file