(Ȱ+ș8ȫ7 EXHAUST ACCESSORIES HELMETS & AUDIO 631 TRICK BOX BYPASS MODULE FOR STOCK "ACTIVE INTAKE & EXHAUST SEAT SYSTEM" 633 O2 SENSOR BUNG PLUGS 635 STOCK REPLACEMENT O2, OXYGEN OR LAMBDA SENSORS EXHAUST ELECTRIC & LIGHT ENGINE ELECTRICS INTAKE ENGINE PRIMARY & CLUTCH TRANSMISSION GASKET & SEALS FINAL DRIVE WHEELS & TIRES BRAKE HANDLEBAR, HAND CONTROLS & MIRRORS CONTROL CABLES & HYDRAULIC LINES FOOT CONTROLS FRONT FORKS FRAME & REAR SUSPENSION FENDER & STRUTS Harley used the Active Intake System (AIS) on 2007 Touring and 2007 thru 2015 Dyna & Softail and the Active Exhaust System (AES) on the European 2007 thru 2016 Dyna & Softail to comply with the latest EU noise emission regulations. The AIS creates a problem for those who want to install an aftermarket air cleaner as removal of the air cleaner back plate will cause the AIS to light a "Fault" warning light on the dash. Installation of this Trick Box Bypass module fools the OEM on-board computer and eliminates the "Fault" light problem. The AIS Trick Box is an OEM style connector that simply plugs into the 2-way socket in stead of the stock Active Intake solenoid plug. The Active Exhaust System (AES) is an ECM-controlled electric motor to open or close a valve in the exhaust system to meet the EU exhaust noise standards. For those who want to install a complete aftermarket exhaust system it is necessary to trick the ECM "Fault" warning module to prevent the warning light coming on on the dash. The AES Trick Box also plugs into the stock wiring harness and replaces the signal from the original exhaust stepper motor and stops the light coming on. 745584 Set of two by-pass modules for use with aftermarket air cleaner (without Active Intake System) & and aftermarket exhaust (without Active Exhaust System) 702022 Active Intake System bypass module only GAS & OIL TANK These M18x1.5 plugs are used when you do not want to use the O2 sensors on fuel injected Sportster models 2007 to present, Softail and Dyna 2007-2011 and Touring models 2007-2010. 735750 M18 x1.5 O2 sensor bung plugs, pair 27878 O2 SENSOR ADAPTER INSERT Insert allows the installation of a 3-wire heated and M12x1.25 threaded O2 sensor in a M18x1.5 threaded bung for a wide band O2 sensor. 758590 O2 sensor adapter insert, each 6962 EXHAUST GASKETS FOR VROD Strongly recommended to replace when re-fitting the stock headers or an aftermarket exhaust sustem. These USA made O2 (Oxygen) sensors (also known as Lambda sensors) meet or exceed factory specifications and feature extra high temperature dual shield ends. They come pre-wired with the connectors installed for a direct fit without any modifications. Sold each. Front OEM Rear OEM XR Sportster 2008-2013 A. 747561 27690-08 A. 747561 27690-08 XL Sportster 2007-2013 B. 747465 27719-07 B. 747465 27719-07 XL Sportster 2014-up C. 747560 32700026 C. 747560 32700026 V-Rod 2008 D 747467 27703-08 D. 747467 27703-08 V-Rod 2009-2011 E. 747466 27683-07 D. 747467 27703-08 V-Rod 2012-2017 F. 747558 32700005 H. 747559 32700006 Dyna 2006-2011 E. 747466 27683-07 E. 747466 27683-07 Dyna 2012-2017 F. 747558 32700005 H. 747559 32700006 Softail 2007-2011 E. 747466 27683-07 E. 747466 27683-07 Softail 2012-up F. 747558 32700005 H. 747559 32700006 Touring 2007-2008 B. 747465 27719-07 B. 747465 27719-07 Touring 2009 B. 747465 27719-07 E. 747466 27683-07 Touring 2010-up G. 747556 27729-10 I. 747557 27809-10 6961 EXHAUST GASKETS FOR XG STREET 636 OXYGEN SENSOR SOCKET TOOL GAUGES&DASHES 637 SONIC SWIVEL STYLE O2 SENSOR WRENCH OIL, OIL FILTERS & OIL COOLERS HARDWARE WINDSHIELD Professional chrome-vanadium tool with LUGGAGE 22mm 180 degree swivel style head to remove and install O2 sensors, also known as Oxygen sensors or Lambda sensors, in TOOLS&CHEMICALS hard-to-reach positions. 745651 Swivel style 22mm sensor wrench TECH TIPS & CROSS REF OEM>ZPN Fits 2002-2008 V-Rod 751439 Stock replacement, set of two (OEM 65109-01) 751460 Set of two, compressed wire with graphite, James (OEM 65109-01) 760072 Set of two, graphite, Cometic (OEM 65109-01) 760057 Set of two, knitted stainless, Cometic (OEM 65109-01) Fits 2009-2017 V-Rod 751482 Set of two, compressed wire with graphite, James (OEM 64971-09) Strongly recommended to replace when re-fitting the stock headers or an aftermarket exhaust system. Fits 2015 to present XG500 Street, XG750 Street and XG750 Street Rod 790067 Set of two, compressed graphite and wire mesh, James (OEM 65900011) This tool is used to remove or install the oxygen sensor on all FLH and FLT series Touring models 2006 thru 2009, Softail, Dyna and V-Rod 2006 thru 2011, 2007 to present Sportster and closed loop fuel injected Buell models. Socket has a 3/8" drive receiver or can be used with a 7/8" wrench. Socket will withstand up to 125 lb/ft of torque. 751055 Fits all unheated Fuel Injected Oxygen Sensor equipped models 2006-present ALPHABETICAL INDEX 03-106
Download PDF