3Ȫ,ȥ$Ȫ< &Ȥ8Ȭ&Ƞ PRIMARY HOUSING & COVERS HELMETS & AUDIO 2514 VENTED CHROME OUTER PRIMARY COVERS SEAT 2515 CHROME PLATED INNER PRIMARY COVER FOR SOFTAIL MODELS 2516 OFFSET INNER PRIMARY COVER FOR SOFTAIL MODELS EXHAUST ELECTRIC & LIGHT ENGINE ELECTRICS INTAKE ENGINE PRIMARY & CLUTCH TRANSMISSION GASKET & SEALS These vented primaries are designed specifically for those who are using an up to 13/4" wide belt drive. The vented slots provide an improved airflow to keep belt running cool thus improves belt life. Fits 4 Speed Big Twins 1970 thru 1984 and 5 Speed Softail models thru 1988. The cover is ready to install on all 8-hole primaries and also features a flat boss that can be drilled when the ninth hole is needed. Installation on floor board equipped FL models requires the drilling and tapping of the mount tab on the provided flat boss in front of the inspection cover. Starter shaft needle bearing must be ordered separately. 210221 Fits 1970 thru 1984 4 Speed Shovelhead and 4- and 5 Speed Softail models 1984 thru 1988 231460 Needle bearing starter shaft (OEM 9063) FINAL DRIVE WHEELS & TIRES BRAKE 2518 VENTED CHROME OUTER PRIMARIES FOR DYNA AND SOFTAIL HANDLEBAR, HAND CONTROLS & MIRRORS CONTROL CABLES & HYDRAULIC LINES FOOT CONTROLS Reinforced inner primary covers that have superior strength over the OEM counterpart and can be used as an OEM replacement part but are recommended if you run a High Performance engine.The reinforcement ribs prevent the cover from cracking at the bearing area under the heavy loads that are common with today's stroker and Big Block engines. Covers have a beautiful chrome plated finish and are available for Softail models from 1990 thru 2006. These Inner primary covers are available with or without seal, bearing, bushing and retaining ring. Lock tab kit must always be ordered separately. Looks even better when fitted in combination with our chrome outer primary cover ZPN210117 or 210118. 210095 Cover only, fits 1990 thru 1993 Softail models (OEM 60630-90) 210114 Cover with seal, bearing, bushing and circlip, fits 1990 thru 1993 Softail models (OEM 60630-90) 210106 Cover only, fits 1994 thru 2006 models (OEM 60630-94) 210115 Cover with seal, bearing, bushing and circlip, fits 1994 thru 2006 models (OEM 60630-94) Replacement seal, bearing, bushing and lock tab kit 231237 For use with 1990 thru 1993 inner primary 231238 For use with 1994 thru 2006, except 2006 Dyna These primaries eliminate the use of spacers and spacer rings to off set the primary when a your Softail is converted to accept a wide tire kit. The engine to primary spacer as well as the transmission to primary spacers are an integrated part of these trick primaries. The elimination of the spacers creates a more rigid primary and provides a much cleaner look. Primaries are available in two off-sets 1" (25.4mm), and 1 1/2" (38mm) offset. They also have the same reinforcement features our other inner primaries have and can be used in combination with High performance engines. The reinforcement ribs prevent the cover from cracking in the bearing area under the loads that are common with today's Stroker and Big Cubic Inch engines. Covers have a beautiful chrome plated finish for that custom appeal and are available for Softail models from 1990 thru 2006. Seals, bearings, bushings, lock tabs and other hardware must be ordered separately. Looks even better when fitted in combination with our chrome outer primary cover ZPN210082. Note: These inners must be used with extended shafts, found elsewhere in this catalog. Fits 1990 thru 1993 Softail models 210155 1 1/2" (38mm) offset Fits 1994 thru 2006 Softail models 210163 1" (25.4mm) offset FRONT FORKS FRAME & REAR SUSPENSION FENDER & STRUTS GAS & OIL TANK GAUGES & DASHES Vented primaries are for use with an up to 1 3/4" wide aftermarket primary belt drive. The vent slots provide an airflow to keep the belt running cool for improved belt life. Matching derby and inspection covers are available seperately. 210149 Vented outer primary fits 1989-1993 Softail and Dyna 210206 Vented outer primary fits 1995-1998 Softail and Dyna. Also fit 1999-2006 Softail and 1999-2005 Dyna when installed with a 3-hole derby cover 301020 Vented chrome CNC Aluminum derby cover 210220 Vented chrome CNC Billet inspection cover Replacement parts 292216 Lock tab, Zodiac, each (OEM 33318-85) 231172 Main shaft seal 1984 to present, James (OEM 12052) 231173 Starter shaft seal 1989 thru 1993 (OEM 12053) 700470 Starter shaft seal 1994 thru 2006 (OEM 12066) 233823 Transmission main shaft support bearing (OEM 9135) 231480 Bearing retaining ring (2), 10-pack (OEM 60678-85) 231478 Starter motor bushing 1990 thru 1993 (OEM 33445-89) 231479 Starter motor bushing 1994 thru 2006 (OEM 33445-94A) Replacement parts 292216 Lock tab, Zodiac, each (OEM 33318-85) 231172 Main shaft seal 1984 to present, James (OEM 12052) 231173 Starter shaft seal 1989 thru 1993 (OEM 12053) 700470 Starter shaft seal 1994 thru 2006 (OEM 12066) 233823 Transmission main shaft support bearing (OEM 9135) 231480 Bearing retaining ring (2), 10-pack (OEM 60678-85) 231680 Bearing retaining ring (2), (OEM 60678-85) 231478 Starter motor bushing 1990 thru 1993 (OEM 33445-89) 231479 Starter motor bushing 1994 thru 2006 (OEM 33445-94A) OIL, OIL FILTERS & OIL COOLERS HARDWARE WINDSHIELD LUGGAGE TOOLS & CHEMICALS TECH TIPS & CROSS REF OEM>ZPN ALPHABETICAL INDEX 08-004
Download PDF